page last updated: 01-01-2009 22:04:56 CET


 Gsm Alarm
 Sim Readers
TSI v.1.0
UDK v3.5
UPI v2.5
USI v1.7
TDM v1.0
TSI v1.0 Kit
 Gsm Gate Control

 Payment methods
 Delivery methods

Here you can find the WM passport of our WM identifier 160947706261
 TiVald Sim Interface v1.0 Kit  

TiVald Sim Interface v1.0 Kit

Price: 0.00 USD

TiVald Sim Interface v1.0 Kit

TiVald Sim Interface v1.0 KIT - you can clone or back up to 8 cards into 1 Silver card (in complete set) using our device. Also phone book reading, SMS editing, PIN management and etc!
Stock OUT & Product discontinued !!!

Before reading of a SIM-card to remove from it a pin-code request. Insert a Your SIM-card into TiVald Sim Interface (Sim Reader/Writer).
1. Choose mode on Sim Reader/Writer - 'Sim Reader'.
Sim Clock: 3.579 or 7.159 (Sim clock 14.318 supports limited quantity of cards, so most likely in this mode the card will not be read out. Nevertheless you can try to read out the card on the above frequency, the smaller time will be borrowed for reading a card).

Sim Reset: 'Low Reset' or 'High Reset'.

Sim data: 'Sim Reader'. 


2. Installation.

Run "install.bat". This will create directory 'c:Sim_Scan' and copy appropriate files.

Start the program sim_scan.exe and to choose the COM-port and COM-port speed.

Please note that the speed of com port should coincide with the speed you have chosen on sim reader.

Press Find Ki, this process can take up to 2 hours.

If all has successfully passed, in the directory 'c:Sim_Scan' the program will keep a file "imsi_ki.dat" in which there will be IMSI and Ki data.

Please note !!!

  1. Your card may be broken during the work with this program!!!
  2. Full calculation time of IMSI and KI codes takes more than 2 hours, so never leave a GSM-card without supervision for a long time, to prevent its non-authorized cloning!!!
  3. Do not use Sim Scan program with SOMEONE OTHER'S SIM CARDS, you may use it only in educational purposes!!!
  4. We are not responsible for any problems, losses and damages!!!
3. Preparation of Silver, Green or Green2 cards.
Remove a Your SIM-card from Sim Reader/Writer and insert Silver, Green or Green2 card into the Sim Reader/Writer. 

Start icprog.exe, and choose the COM-port: 

Ok-> Settings-> Options-> Smartcard, choose the COM-port and Frequency


Ok -> Settings -> SmartCard (Phoenix):

Choose in IC-Prog microcircuit PIC 16F877 (for silver, green and green2 cards), and in IC-Prog open file SIM_EMU_FL_6.01_ENG.hex from folder SimEmu 6.01:


If you want the card was programmed with additional protection against reading, choose CP 1F00h-1FFFh in menu Code Protect and enable CPD by tick (recommended)

Choose mode on Sim Reader/Writer - 'Program Pic'.
Sim Clock: 'Program Pic'.

Sim Reset: 'Program Pic'.

Sim data: 'Program Pic'.

After all adjustments press the button    and wait, while the PIC-processor of a card will be programmed.

After the PIC processor is programmed choose next modes on Sim Reader:
Sim Clock: 3.579

Sim Reset: 'Low Reset' or 'High Reset'.

Sim data: 'Sim Reader'. 


Next choose in IC-Prog a microcircuit 24C64 (for Silver card), 24C128 (for Green card) or 24C256 (for Green2 card):

Open file with an EEPROM dump, corresponding to your card, for example SIM_EMU_EP_6.00_ENG.hex. After that press the button    and wait, while EEPROM area in the card will be programmed.

Now, when the card is inserted in the phone a new menu 'SimEmu' will appear. With this menu you can bring in preliminary read out IMSI and Ki codes onto a card and many other things. More detailed information about SimEmu is possible to find on a developer's page.

Software download:

SimScan 2.01
WoronScan 1.06
IC-Prog 1.05
Configured files SimEmu 6.01 for Silver, Green and Green2 cards

« Back


Now in cart

0 products
overall value:
0.00 USD

 Check the basket
 Make order

Change currency

$ USD   € EUR

Vote for us

TOP 100 GSM Fox

Mailing List

Subscribe newsletter if you want to be informed about news and special offers. Just enter your email adress and click 'Subscribe'